Estágio realizado na Amorim & Irmãos, S. A. - Investigação e Desenvolvimento e orientado pelo Doutor Miguel Cabral ; Tese de mestrado integrado. Engenharia Química. Faculdade de Engenharia. Universidade do Porto. 2010
In this work, microwave hybrid sintering at 1300 and 1350 °C was carried out for densification of La9.33Si2Ge4O26 mechanically alloyed powder with apatite structure. The pellets sintered at these two temperatures present the same structure (apatite) with relative densities of 92 and 96%, respectively. Mechanical analysis performed on sintered materials revealed the following results: hardness of 7.1 and 8.0 GPa...
Apatite-type rare earth based oxides, such as R-doped lanthanum oxides of general formula La9.33(RO4)6O2 with R = Ge, Si, exhibit high ionic conductivity and low activation energy at moderate temperatures, when compared to the yttria-stabilized zirconia electrolyte making them potential materials to be used in the range 500–700 °C, for intermediate temperature solid oxide fuel cells (IT-SOFCs). In this study, d...
Solid oxide fuel cells (SOFCs) are devices that allow direct conversion of chemical to electrical energy through an electrochemical reaction in a cleaner and more efficient way than conventional processes (eg. gas turbines). They are characterized by the use of a solid oxide material as the electrolyte. Yttria-stabilised zirconia (YSZ) has traditionally been used in SOFCs electrolytes at temperatures in the ra...
Powders of La2O3, GeO2 and SiO2 were dry milled in a planetary ball mill with different rotation speeds (150–350 rpm) and increasing milling times up to 35 h in order to obtain the La9.33Si2Ge4O26 apatite phase at room temperature. The results showed that the higher the rotation speed the lower the time required for the formation of the apatite phase. No reaction between the starting powders was observed at 150...
Mechanical properties of La9.33Si2Ge4O26 prepared by mechanical alloying and subsequent sintering at 1300–1400 °C for 1 h were evaluated. Hardness and Young's modulus values in the range 7.3–9.6 GPa and 106–135 GPa, respectively, were obtained from nanohardness tests. The fracture toughness values derived from the Palmqvist method varied between 3.5 and 3.9 MPa m1/2 from classical microindentation test with an ...
Dissertação de mest., Ciências Farmacêuticas, Faculdade de Ciências e Tecnologia, Univ. do Algarve, 2012 ; O envelhecimento global é uma realidade para a qual a sociedade mundial ainda se está a adaptar. A evolução do conhecimento científico e o surgimento de novos medicamentos, cada vez mais sofisticados e eficazes, tem contribuído, e muito, para este facto, pois cada vez mais se conseguem bons resultados no ...
Introdução: O aumento da esperança média de vida tem vindo aumentar ao longo dos anos o que implica um aumento da percentagem, de pacientes polimedicados e portadores de patologias. Perante esta constatação, é essencial que o Médico Dentista adapte a sua prática clínica a uma população cada vez mais complexa, tornando-se fundamental a avaliação do risco médico. O risco médico é caracterizado segundo uma escala ...
O principal objectivo deste trabalho é estudar as propriedades estruturais, eléctricas e magnéticas de filmes multicamada de manganites de lantânio bário e titanato de bário. Para tal efeito foram depositados filmes multicamada de manganites de bário e de titanato de bário alternadamente sobre diferentes substratos. Foi feita uma análise estrutural, eléctrica e magnética aos filmes. Através da análise estrutura...
Introdução: A Motor Assessment Scale (MAS) tem mostrado ser um instrumento válido e fidedigno na avaliação do progresso clínico de indivíduos que sofreram um Acidente Vascular Cerebral (AVC). Objectivos: Traduzir e adaptar a MAS à realidade portuguesa e contribuir para a validação da versão portuguesa, avaliando a sua consistência interna. Metodologia: Após um processo de tradução, revisão por peritos, retrover...
Financiadores do RCAAP | |||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |